Documentation
Search documentation and knowledge articles, review an agent answer with follow-up questions, and escalate to Robotics Support when the guidance does not resolve the issue.
Verify that the cable shield (drain wire) is correctly terminated to a chassis ground ... Perform LOTO and swap the field wiring between the two channels at the module's ... If the problem
During high-load movement on Joint 3, the controller reports unstable servo behavior that ... Root Cause Analysis ... Verify drive parameters and protocol alignment with controller settings.
NexBot S-5 (SCARA) Compatibility is determined by the overall safety cell design and risk assessment, ... Ensure the fencing provides the required safety distance from the robot's maximum ...
Electrical Connection: Connect the 24VDC power and IO-Link communication cable to the ... Operation ... Verify Grip: Use the IO-Link feedback to program a grip verification step. ... Keywords
A stable, level conveyor is non-negotiable for reliable robotic interaction. ... Prerequisites: ... Adjust each foot until the conveyor frame is perfectly level in both the direction of travel ...
Place a suitable oil drain pan beneath the drain plug. ... 3. Filling the Gearbox ... Reinstall the drain plug and tighten it using a torque wrench to the value specified in the ... Keywords
Check for cuts, abrasions, or tight bends that could damage the internal conductors. ... Power on the system and navigate to the I/O or Diagnostics screen on the teach ... NXB-SNS-ENC521-013).
Once the cover is removed, you will see the drive motor, pulleys, and the old timing ... Do not remove the tensioning hardware completely. ... 4. Inspection and Cleaning ... Unpack the new
Note the specific joint number (e.g., J2, J4). Disassemble the Joint: ... Do not remove them completely yet. Inspect Alignment Components: Carefully separate the joint components.
Article ... Do not use liquid cleaners directly on the module. ... Identify the screw terminals for power and I/O signals. ... The recommended torque value for these terminals is 0.4 Nm.
During high-load movement on Joint 3, the controller reports unstable servo behavior that ... Root Cause Analysis ... Verify drive parameters and protocol alignment with controller settings.
IO-Link Integration ... Configuration Steps: ... The Master should automatically detect the device. Using the configuration software, you can access and set device parameters such as ...
Weight 0.35 kg Material Anodized Aluminum Voltage 24VDC IP Rating IP67 Country of Origin IT Protocol PROFINET Dimensions 58 x 58 x 45 mm
Step 3: Dowel Pin Insertion ... Warning: Excessive force can cause the hardened pin to fracture or damage the ... Slide the component onto the shaft, ensuring the key engages smoothly into the ...
Digital multimeter ... Connect the IO-Link signal wire (C/Q) to the corresponding pin on the M12 connector, ... Upload the IODD file if required and configure basic parameters such as gripping ...
Unit Weight 0.8 kg Material Polycarbonate/ABS Blend Voltage 24VDC IP Rating IP20 Country of Origin CH Protocol PROFINET Dimensions
This connector is intended for use by qualified technicians to terminate DeviceNet ... 4. Operation ... The NET533-013 is designed for a secure shield connection; ensure the drain wire or ...
Technical Specifications Parameter Value Unit Weight 0.01 kg Material Thermoplastic Elastomer (TPE) IP Rating IP67 Country of Origin JP
This product must be used as part of a complete safety system. ... 4. Operation ... Active State (Actuated) ... The safety controller detects this change of state and immediately issues a stop ...
Parameter ... Stainless Steel 304 Country of Origin CH ... © 2026 NexBot Robotics. All specifications subject to change without notice. Document ID: DS-NXB-GEN-833-007-1.0
Use a calibrated torque wrench to tighten the mounting bolts in a star pattern. ... Step 4: Step 4: Connect Power and IO-Link Cables ... Step 7: Step 7: Update Robot Payload Settings
Doing so can damage sensitive encoders, bearings, or shafts, leading to costly ... Warning: Over-tensioning the belt will cause excessive load on motor bearings, ... © 2026 NexBot Robotics.
This guided process will prompt you for essential information, including motor type, ... The mode is typically selected by the EtherCAT master controller based on the ... Performance Tuning
Image Acquisition Settings Optimize the 3D data quality by adjusting exposure time, gain, and projector ... Defining a Region of Interest (ROI) ... Job Configuration and PLC Integration